DAQ_TRAINER

VARIOUS SENSORS USING DATA ACQUISITION

FEATURES

  • Circuit diagram printed on pcb
  • Transformer based power supply
  • USB software controlled
  • Onboard DC supply as per requirement of the trainer
  • All components on back side to avoid any physical damage
  • Onboard DPM meter
  • Strongly support by systematic operating instructions

TECHNICAL SPECIFICATIONS

  • Acquisition of various sensor O/P using USB DAQ
  • To study of transducer like : (available independently or combined)
  • RTD / Thermocouple Transducer
  • Pressure Sensor Transducer
  • Stain Gauge Transducer
  • Onboard 3.5 digit Digital panel meter
  • USB software controlled
  • Signal conditioning, instrumentation circuitry
  • Test points provided on board at various stages to observe the signals & waveforms
  • Interconnection : 2/4mm banana sockets
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet with cover
  • Standard Accessories : User’s Manual with patch cords

DAQ

ULTRASONIC_TRAINER

ULTRA SONIC KIT

FEATURES

  • Block diagram printed on front panel
  • Transformer based power supply
  • Onboard DC supply as per requirement of the kit
  • All components on back side to avoid any physical damage
  • Strongly support by systematic operating instructions

TECHNICAL SPECIFICATIONS

  • Study of Ultrasonic Transducer for distance measurement
  • Ultrasonic Transducer Range : 56cm to more then 5 meter
  • Burst Signal : 40KHz
  • Amplifier : 60db
  • Display type : LCD
  • Onboard AC supply of 16V
  • Onboard DC supply of 9V
  • Buzzer indicator
  • Test Points : more than 12 nos.
  • Automatic OFF in 60s (stand by mode)
  • Accuracy : ±0.5% of the reading
  • Signal conditioning, instrumentation circuitry
  • Interconnection : 2/4mm banana sockets
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet with cover
  • Standard Accessories : User’s Manual with patch cords
TANK_LEVEL

FLOW RATE MEASUREMENT KIT

FEATURES

  • Block diagram printed on front panel
  • Transformer based power supply
  • On board Digital Meter
  • Turbine enclosed inside a plastic case to ensure leak proof safety measure
  • Strongly support by systematic operating instructions

TECHNICAL SPECIFICATIONS

  • Study of Flow Rate measurements
  • 1/2 HP, 230V AC Pump
  • Digital panel meter for flow rate measurement
  • Potentiometer for controlling the speed of fluid through pump
  • Rotameter in Acrylic Glass tube type placed vertically for flow rate measurement
  • Range : 0 to 660LPH
  • Signal conditioning circuit
  • Open top water tank
  • Test points are provided to observe the signals and waveforms
  • Push button provided on front panel to reset the counter
  • Separate ON/OFF switches for Pump and trainer
  • Manual Valve for controlling the amount of fluid flowing through the pipe
  • Inbuilt power supply
  • 230V/50Hz mains operated.

FLOW-PIC1

PHOTO_ELECTRIC_SENSOR

PHOTO ELECTRIC SENSOR KIT

TECHNICAL SPECIFICATIONS

  • Study of measurement of photo electric pickup transducer
  • RPM meter for measurement of speed
  • On-board potentiometer for varying speed
  • On-board photo electric sensor and DC motor with shaft
  • On-board push button to reset the count
  • On-board signal conditioning circuit
  • Test points are provided at different stages to observe the signals and waveforms
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supplies
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet
  • Accessories : User’s Manual with patch cords
HUMIDITY_SENSOR

HUMIDITY SENSOR KIT

TECHNICAL SPECIFICATIONS

  • To study of humidity sensor transducer
  • Humidity transducer capacitive for 90% non condensed range 0 to 100%
  • RH humidity chamber generator (water tank)
  • 3.5 digit display voltmeter thru 20 turn pot/preset.
  • Sockets at different points for observations
  • Built in IC regulated power supply
  • Interconnection : 2/4mm banana sockets
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet with cover
  • Accessories : User’s Manual with patch cords
PHOTO_SENSOR

PHOTO SENSOR KIT

TECHNICAL SPECIFICATIONS

  • Study of Photo Sensor Transducers
  • Photo Conductive Cell (LDR)
  • Photo Junction Devices/Photo Conductor (Photo Diode/Photo Transistor)
  • Photo Voltaic Cell (Solar Cell)
  • Light Source : Lamp with variable intensity (controlled by using SCR)
  • Potentiometer for controlling input as a load etc.
  • Onboard signal conditioning circuit
  • Onboard 3.5 digit DPM meter
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supplies
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet
  • Accessories : User’s Manual with patch cords
Piezo_Electric

PIEZO ELECTRIC PICKUP TRANSDUCER KIT

TECHNICAL SPECIFICATIONS

  • Measurement of pressure using Piezo Electric Transducer
  • Industry standard Piezo Electric transducer
  • Instrumentation amplifier with variable gain
  • On-board potentiometer for adjusting GAIN
  • 3.5 digit DPM
  • Sockets at different points for observations
  • Built in IC regulated power supply
  • Interconnection : 2/4mm banana sockets
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet with cover
  • Accessories : User’s Manual with patch cords
capacitive_pickup

CAPACITIVE PICKUP KIT

TECHNICAL SPECIFICATIONS

  • Variable condenser (gang condenser) as transducer
  • OP amp based signal conditioning circuit
  • Built in ac excitation source
  • Test Point for measuring Signals
  • 3.5 digit DPM for indication of displacement
  • Sockets provided to study the process to find out the error rate
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supplies
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet with cover
  • Accessories : User’s Manual with patch cords
LDR-OPTO

LDR/OPTO ISOLATOR KIT

TECHNICAL SPECIFICATIONS

  • Study of Light Dependent Resistor as light intensity measuring transducer
  • Sockets for LDR to measure resistance at different intensity levels t
  • 1st degree linearization circuit
  • Unbalance Bridge for LDR interface
  • 12 volt 21 watt tungsten lamp with intensity control ( continuously variable )
  • Calibration graph supplied with the tutor Luxmeter (optional)
  • 3.5 digit DPM as light intensity indicator
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supplies
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet
  • Accessories : User’s Manual with patch cords
TORQUE_TRANSDUCER

TORQUE MEASUREMENT KIT

TECHNICAL SPECIFICATIONS

  • Range : 0 to 1 Kg – m
  • Resolution : 0.1 kg/m.
  • Excitation : 5 Volts DC
  • Analog Output : 2 Volts, FSD
  • With 4 Nos. Weight of 250 gm
  • 3.5 digit DPM as displacement indicator
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supplies
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet with cover
  • Accessories : User’s Manual with patch cords
THERMISTOR

THERMISTOR KIT

TECHNICAL SPECIFICATIONS

  • Study of thermistor as temperature measuring transducer
  • Mecury thermometer and heater 10W (optional)
  • Thermistor ( NTC ) mounted in metallic tubing and protected from corrosion
  • Study of non-linear characteristics
  • Unbalance Bridge circuit with 1st degree linearization
  • Differential gain amplifier
  • 3.5 digit DPM as temperature scale
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supplies
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet
  • Accessories : User’s Manual with patch cords
Opticsl_Trans_Trainer

OPTICAL TRANSDUCER KIT

FEATURES

  • Self contained kit
  • Functional Block printed on pcb
  • Onboard 4 different types optical sensor
  • Onboard Digital Panel Meter
  • Inbuilt Power Supply
  • Onboard Signal Conditioning Circuit
  • Strongly support by systematic operating instructions

TECHNICAL SPECIFICATIONS

  • Transducers : 04 nos. :

a) Photo Conductive Cell

b) Photo Transistor

c) Photo Voltaic Cell

d) Pin Photo Diode

  • Signal Conditioning Circuitry :

a) DC Amplifier

b) Power Amplifier

c) Buffer

d) Comparator

e) Electronic Switch

f) Current Amplifier

  • Light Source : Filament Lamp
  • Input Circuits : Rotary & Slide Potentiometers
  • Output Circuits : Relay & LED
  • Onboard Digital Volt Meter
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supplies
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet with cover
  • Standard Accessories : User’s Manual with patch cords

EXPERIMENTS

  • Characteristics of Filament Lamp
  • Characteristics of Photo Conductive Cell
  • Characteristics of Photo Transistor
  • Characteristics of Photo Voltaic Cell
  • Characteristics of Photo Diode
  • Light Controlled Switch System
TT-TTT

TEMPERATURE TRANSDUCER KIT

FEATURES

  • Self contained kit
  • Functional Block printed on pcb
  • Onboard 4 different types temperature sensor
  • Onboard Digital Panel Meter
  • Inbuilt Power Supply
  • Onboard Signal Conditioning Circuit
  • Strongly support by systematic operating instructions

TECHNICAL SPECIFICATIONS

  • Transducers : 04 nos. :

a) NTC Thermistor

b) Platinum RTD

c) Thermocouple (K type)

d) IC Temperature Sensor

  • Signal Conditioning Circuitry :

a) Instrumentation Amplifier

b) X100 Amplifier

c) DC Amplifier

d) Comparator

e) Electronic Switch

  • Heating Source : Wirewound Resistance
  • Input Circuits : Rotary & Slide Potentiometers
  • Output Circuits : Relay & Buzzer
  • Onboard Digital Volt Meter : 2V and 20V (switch selectable)
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supplies
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet with cover
  • Standard Accessories : User’s Manual with patch cords

EXPERIMENTS

  • Characteristics of NTC Thermistor
  • Characteristics of Platinum RTD
  • Characteristics of K-type Thermocouple
  • Characteristics of Temperature Sensor
Mag-pickup-sensor

INDUCTIVE PICKUP KIT

TECHNICAL SPECIFICATIONS

  • Study of measurement of inductive pickup
  • RPM meter for measurement of speed
  • Potentiometer for varying speed (0-2400 RPM)
  • Inductive sensor and DC motor with shaft
  • On-board signal conditioning circuit
  • Test points are provided at different stages
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supplies
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet
  • Accessories : User’s Manual with patch cords

DISTANCE MEASUREMENT

  • All the above specification remain same including :
  • Study of distance measurement
  • DPM meter for measure distance & count
  • On-board push button to reset the count
Mag-pickup-sensor

MAGNETIC PICKUP KIT

TECHNICAL SPECIFICATIONS

  • Study of speed measurement by variable reluctance transducer
  • 12 V, 2400 RPM permanent magnet DC motor
  • Speed controller ( 0 – 2400 RPM )
  • Electromagnetic pick up
  • Signal conditioner circuitry (OPAMP based)
  • Excitation voltage for pick up
  • 4 digit digital counter for speed display
  • Test points at various places
  • Electronic tachogeneration
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supplies
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet
  • Accessories : User’s Manual with patch cords
ANGULAR_DISPLACEMENT

LINEAR DISPLACEMENT KIT

TECHNICAL SPECIFICATIONS

  • Linear potentiometer as linear displacement measurement transducer (0-100mm) using mechanical attachment with vernier
  • Op amp in signal conditioner circuit
  • Offset adder for position modulation
  • 3.5 digit DPM to read displacement
  • Constant calibrated
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supply
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet with cover
  • Accessories : User’s Manual with patch cords
Load_Cell

LOAD CELL KIT

TECHNICAL SPECIFICATIONS

  • Study the principle/working of load cell & its applications to measuring load
  • Bridge made up of 4 strain gauges mounted on a specially alloy materials type load cell
  • Built in excitation voltage for the bridge
  • 3.5 digit SSD for direct reading stain in Kg.
  • Built in highly sensitive signal amplifier
  • Multi turn potentiometer for zero adjustment
  • Different loads provided for building up of load
  • Test pins for monitoring at all stages
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supplies
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet
  • Accessories : User’s Manual with patch cords
ANGULAR_DISPLACEMENT

ANGULAR DISPLACEMENT KIT

TECHNICAL SPECIFICATIONS

  • Servo potentiometer as angular displacement measurement transducer (full 0-360°) using calibrated dial with 2° resolution
  • Op amp in signal conditioner circuit
  • Offset adder for position modulation
  • 3.5 digit DPM to read displacement
  • Constant calibrated
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supply
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet with cover
  • Accessories : User’s Manual with patch cords
STRAIN_GAUGE

STRAIN GAUGE KIT WITH CANTILEVER

FEATURES

  • Self-contained and easy to operate
  • Sensitive, Linear, stable & accurate
  • Test-points to observe input output of each block
  • Onboard gain adjustment & offset null adjustment
  • Built in DC power supplies
  • 3-1/2 digits LED display
  • Onboard cantilever arrangement
  • High repeatability and reliability

TECHNICAL SPECIFICATIONS

  • Parameter Measured :    Strain in terms of grams on a cantilever beam
  • Measurement System :    a] Weights

        b] Transducer with electronic instrumentation

  • Transducer :    Temperature compensated strain gauge
  • Type :    Cu-Ni foil with polyamide carrier base
  • Gauge Resistance :    350 Ohms (Nominal)
  • Gauge Length :    6mm
  • Gauge Width :    4 mm
  • Gauge Base :    5 mm x 4.3 mm
  • Gauge Factor :    2:1 (approx.)
  • Transducer :    Strain gauges mounted on a stainless steel Measurement  cantilever beam
  • Configuration :    Bridge with two arms as strain gauges (Wheatstone Bridge principle)
  • Range :    Upto 1 Kilogram
  • Actual Strain :    By various weights to be placed in a pan fixed with the  beam
  • Excitation Source :    DC Regulated source
  • Tare Adjustment :    Zero adjustment by a potentiometer
  • Readout :    5 digit digital display to indicate strain in kilograms
  • Test Points :    Test points are provided at various stages in the circuit to observe waveforms and voltages
  • Power Requirements :    230V, ± 10% AC, 50Hz.
  • Standard Accessories  :           Detailed Instruction Manual.
PRESSURE_MEASUREMENT

PRESSURE MEASUREMENT KIT

TECHNICAL SPECIFICATIONS

  • Range :- 0 -10 KG/300mm.
  • Pressure Cell
  • Pressure generator with dial display
  • Pressure Valve -01 no. (manually)
  • Sockets at different places for observing / measuring the signals
  • 3.5 digit DPM as pressure indicator
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supplies
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet with cover
  • Standard Accessories : User’s Manual with patch cords
thermocouple

THERMOCOUPLE KIT

TECHNICAL SPECIFICATIONS

  • Thermocouple with digital panel meter
  • Output for monitoring & control
  • Test pins for monitoring at all stages
  • Mercury thermometer & heater 10 watts (Optional)
  • RS-232C interface to be connected to computer (Optional)
  • 3.5 digit DPM as temperature indicator
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supplies
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet with cover
  • Standard Accessories : User’s Manual with patch cords
RTD

RTD (PT-100) KIT

  • Study of RTD as temperature measuring transducer
  • Mercury thermometer and heater 10W (optional)
  • RTD ( PT – 100 ) probe with protection cover
  • Bridge circuit for transducer
  • Differential amplifier with feedback
  • Lead compensation system
  • Sockets provided to study the process to find out the error rate
  • 3.5 digit DPM as temperature indicator
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supplies
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet with cover
  • Standard Accessories : User’s Manual with patch cords
Load_Cell

LOAD CELL KIT

TECHNICAL SPECIFICATIONS

  • Study the principle/working of load cell & its applications to measuring load
  • Bridge made up of 4 strain gauges mounted on a specially alloy materials type load cell
  • Built in excitation voltage for the bridge
  • Built in 3.5 digit seven segment display for direct reading stain in Kg.
  • Built in highly sensitive signal amplifier
  • Built in multi turn potentiometer for zero adjustment
  • Different loads provided for building up of load
  • Test pins for monitoring at all stages
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supplies
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet with cover
  • Standard Accessories : User’s Manual with patch cords
LVDT

LVDT KIT

TECHNICAL SPECIFICATIONS

  • To study of LVDT as displacement transducer
  • Built in AC excitation source 2.5 kHz typical
  • Linear variable differential transformer in non metallic structure
  • Micrometer attachment with mechanical displacement system
  • Displacement range 0-10 mm
  • Balanced demodulator IC based
  • Onboard potentiometers for Span & Zero Adjustment
  • 5 digit DPM as displacement indicator
  • Interconnection : 2/4mm banana sockets
  • DC Supply : Built in IC regulated power supplies
  • 220V ±10%, 50Hz mains operated
  • Enclosed in an attractive ABS plastic cabinet with cover
  • Standard Accessories : User’s Manual with patch cords
SENSOR_TRAINER

SENSOR KIT

FEATURES

  • Circuit diagram printed on PCB
  • Separate Section for each transducer/sensor for ease of study
  • Transformer based power supply
  • Strongly support by systematic operating instructions
  • Stand alone board for the following transducers :

                                    LVDT TRANSCUDER

  • To study of LVDT as displacement transducer
  • Built in AC excitation source 2.5 kHz typical
  • Linear variable differential transformer in metallic structure
  • Micrometer attachment with mechanical displacement system
  • Displacement range ± 5mm

STRAIN GAUGE TRANSCUDER

  • To study of Strain Gauge transducer
  • Built in DC (3.2V) excitation source for internal bridge balance
  • Strain Gauge Sensor in metallic structure
  • Strain measure upto 500 micro strain (approx) in amplifier output

LOAD CELL TRANSCUDER

  • To study of Load Cell transducer
  • Built in DC (+12V) excitation source for internal bridge balance
  • Load Cell Sensor in metallic structure
  • Load measure upto 1.5Kg

RTD (PT-100) TRANSCUDER

  • Study of RTD as temperature measuring transducer
  • RTD ( PT – 100 ) probe with protection cover
  • Bridge circuit for transducer
  • Differential amplifier with feedback
  • Temperature measurement upto -10°C to 100°C

THERMOCOUPLE TRANSCUDER

  • To study of Thermocouple transducer
  • Thermocouple Sensor in metallic structure
  • Temperature Measurement upto -10°C to 100°C

MAGNETIC PICKUP TRANSDUCER

  • Study of meausrement of magnetic pickup transducer
  • On-board RPM meter for measurement of speed
  • On-board potentiometer for varying speed
  • On-board magnetic sensor and DC motor with shaft
  • On-board push button to reset the count

SMOKE DETECTOR SENSOR

  • Study of smoke detector
  • On-board smoke sensor
  • On-board fire alarm

GENERAL SPECIFICATIONS

  • Sockets at different places for observing / measuring the signals
  • 5 digit digital voltmeter meter having range 0-200mV for load cell
  • 5 digit digital voltmeter meter having range 0-2V for LVDT, Thermocouple & Strain Gauge (Switch Selectable)
  • 220 V, Built in IC regulated power supply
  • Enclosed in a attractive wooden cabinet with cover for protection onboard components & sensors.
  • Detailed instruction manual